Measurement of Gaseous Emissions from Animal Housing

Animal housing and manure storage facilities are two principal on-farm sources of gaseous emissions to the atmosphere. The most important pollutants emitted are ammonia (NH3), methane (CH4), and nitrous oxide (N2O).


Introduction
Animal housing and manure storage facilities are two principal on-farm sources of gaseous emissions to the atmosphere. The most important pollutants emitted are ammonia (NH 3 ), methane (CH 4 ), and nitrous oxide (N 2 O).
Ammonia (NH 3 ) is a colorless gas with a pungent smell that can have impacts on environmental and human health (figure 1). Ammonia is emitted by many agricultural activities, including crop production as well as animal production. Ammonia plays a key role in the formation of secondary particulate matter (PM) by reacting with acidic species such as sulfur dioxide (SO 2 ) and nitrogen oxides (NO x ) to form fine aerosols, and is thus called a particulate precursor. The PM created by the reaction of NH 3 and acidic species in the atmosphere contributes to poor air quality including regional haze. These particles have an aerodynamic diameter of less than 2.5 microns and are generally referred to as "PM-fine." They are readily inhaled and populations exposed to PM-fine have greater respiratory and cardiovascular health risks such as asthma, bronchitis, cardiac arrythmia and arrest, and premature death. Some emitted NH 3 is subsequently deposited on land and water downwind of facilities, and can acidify soils and freshwater. The addition of available nitrogen (N) to low-nutrient ecosystems disturbs their balance and can alter the relative growth and abundance of plant species.
Nitrous oxide and CH 4 are potent greenhouse gases (GHGs) which contribute to global warming. The global warming potential (GWP) is a factor specific to each GHG and allows comparisons of the relative global warming impacts between different GHGs. This factor indicates how much heat a given gas traps over a certain time horizon (usually 100 years), compared with an equal mass of carbon dioxide (CO 2 ). Nitrous oxide GWP for a 100-year time horizon is 265 with a lifetime in the atmosphere of 114 years. Methane GWP for a 100-year time horizon is 28 with a lifetime in the atmosphere of 12 years.
Nitrous oxide, also known as "laughing gas," is colorless and odorless, and contributes to the destruction of the atmospheric ozone layer. In agriculture, the main source of N 2 O emissions is soil, from crop fertilizer use, soil cultivation, and spreading of urine and manure. Other sources include industrial processes, and natural processes involving soils and oceans.
Methane is a volatile organic compound, odorless and flammable. In agriculture, the main sources are enteric fermentation (fermentation that takes place in the digestive systems of animals) and the degradation of manure. Methane contributes to ozone formation in the lower atmosphere, and to ozone layer depletion in the upper atmosphere.
Researchers and engineers have developed different approaches to reliably measure and quantify emissions of NH 3 , N 2 O, and CH 4 from animal production facilities. The implementation of these methods helps to understand the production processes, to identify the influencing factors, and to develop mitigation techniques or practices. The specific characteristics of animal housing and the variability of the houses and animal production systems make the development and implementation of the different methods a real challenge.

Animal Houses
Animal housing is designed to provide shelter and protection with control of feed consumption, diseases, parasites, and the interior thermal environment. An animal house is designed to take into account animal heat and moisture production, building characteristics (e.g., insulation and volume), and outdoor climate. Inside the house, animals produce the following critical components that affect emissions: • sensible heat that is transferred to the interior air by means of convection, conduction, and radiation, and causes an increase of air temperature;

Outcomes
After reading this chapter, you should be able to: • Explain how gaseous emissions are formed and released from animal housing • Outline the methods to measure concentrations of ammonia and greenhouse gases • Estimate ventilation rates of selected animal housing • Calculate emissions of ammonia and greenhouse gases from animal housing • latent heat that is generated through the evaporation of moisture from the lungs, skin, urine, and fecal material, and through increases of air humidity; • mixtures of feces and urine, which become a source of gaseous emissions (NH 3 , N 2 O, CO 2 , water vapor, CH 4 ), and heat; and • CO 2 from animal respiration.
The control of temperature, moisture, gas concentrations and dust concentrations inside the house is essential to achieve optimal conditions for animal growth and production. The optimal conditions vary as a function of animal age, species, and breed, and rely on the implementation of ventilation systems. The ventilation system partly controls the rate and total emissions from the building. There are two types of ventilation systems: mechanical and natural. The RAMIRAN European network (RAMIRAN, 2011) defines the two systems as: • mechanical ventilation, which is ventilation of a building, usually for pigs, poultry, or calves, through the use of electrically powered fans in the walls or roof that are normally controlled by the temperature in the building; and • natural ventilation, which is ventilation of a building, e.g., for cattle, by openings or gaps designed into the roof and/or sides of the building.

NH 3 , N 2 O, and CH 4 Emissions Processes in Animal Housing and Influencing Factors
Ammonia is volatilized as a gas during manure management. It is mainly derived from the urea excreted in urine (or uric acid in the feces, in the case of poultry). The process of forming NH 3 from urea is relatively fast and is outlined in figure 2. Once excreted, urea is decomposed within a few hours to a few days into ammonium (NH 4 ) by means of the enzyme urease, which is widely present in feces and soils. Ammonium is in equilibrium with dissolved NH 3 enhanced at high pH values. A second physical equilibrium exists between dissolved and free NH 3 in the manure matrix. Finally, the free NH 3 can be released to the atmosphere. This is a mass transfer process affected by air velocity, diffusion from beneath the surface, and exposure to air on the surface of the manure. This is a continuous process that starts in the animal housing itself and continues  (Snoek et al., 2014).
during manure management and land application. Several factors are involved in the amount of NH 3 emitted to the atmosphere: • manure composition; the most relevant factors are the amount of urea excreted by the animals, the pH of the manure, and its moisture content; • the environmental conditions, particularly temperature and wind speed above the emitting surface; • the facilities for animal housing and manure management; and • management practices, particularly those altering the contact of manure with air, and urine with feces, by reducing time of exposure or contact surface.
On farms, N 2 O originates from the management of manure and its application to land as fertilizer. Emission of N 2 O occurs from the successive nitrification and denitrification of NH 4 . A first aerobic phase is required for the nitrification, while anoxic conditions are required for denitrification (figure 3). These conditions are characteristic of the following situations: • composting with alternative wetting, mixing, and drying periods; • aerobic treatment of slurry; • air cleaners at the air exhaust of the animal house based on biological scrubbing of air; and • application of manure to soil and subsequent drying-wetting events.
Methane is produced during the anaerobic decomposition of organic matter. This occurs mainly during digestion in ruminants and decomposition of manure. In this process, the microbial breakdown of organic matter occurs in different stages, from more complex molecules to the simplest. The main mechanism is presented in figure 4. Apart from the presence of organic matter and anoxic conditions, time (a few weeks) is needed to complete the process, and the process may be inhibited due to certain conditions, such as NH 3 accumulation. In contrast to NH 3 , CH 4 has very low solubility in water and, once produced, is released to the atmosphere through a characteristic bubbling, in the case of slurries.
For enteric fermentation in ruminants, key factors are feed composition and genetics. More  digestible feeds reduce the amount of CH 4 . Feed constituents such as lipids or essential oils may reduce CH 4 production through inhibition. Genetics also influence the amount of CH 4 produced and can be modified through animal genetic selection.
CH 4 emission during manure management is due to the presence of organic matter subjected to anaerobic conditions for sufficient time (about one month, at least) for methanogenic bacteria to develop. The amount and composition of organic matter determines the maximum potential for CH 4 formation. Manure management practices that interrupt anaerobic conditions, reduce the load of organic matter, or feature biogas capture are potentially effective for mitigating emissions.

Measuring Emissions from Animal Housing
The most common approach used to determine gas emission rates from animal houses is based on quantifying ventilation rates and inlet and outlet concentrations of the gas (figure 5). The mass flow rate of emitted gas (emission rate or ER) is proportional to the ventilation rate and the concentration difference between exhaust and outside air. Several different techniques are available to measure gas concentrations inside and outside the house and the ventilation rate.

Gas Concentration Measurement Techniques
The techniques used most often to measure NH 3 , CH 4 , and N 2 O concentrations of animal houses are either physical (optical, gas chromatography, chemiluminescence) or chemical (acid traps, active colorimetric tubes).

Optical Techniques
Optical techniques are based on the Beer-Lambert absorption law, which indicates that the quantity of light of a given wavelength absorbed is related to the number of gas molecules in the light's path that are able to absorb it.
Optical techniques rely on the use of a light source, a chamber to contain the air sample during measurement, and a detector to quantify the target gas absorption. The main techniques used in animal houses are infrared (IR) spectroscopy (photoacoustic or Fourier transform), tunable diode laser absorption spectroscopy (TDLAS), off-axis integrated cavity output spectroscopy Figure 5. Direct emission measurement in an animal house. The difference in concentration between indoors and outdoors and the ventilation rate must be measured (adapted from Calvet et al., 2013).
(OA-ICOS), and cavity ring-down spectroscopy (CRDS). Differences between these techniques include the detection principle of absorption and the type and wavelength of light sources (quantum cascade laser, tunable diode laser, or IR source). Techniques using lasers (a monochromatic source with a narrow band of wavelengths) are more selective, accurate, and stable than techniques with a polychromatic IR source (i.e., large band of wavelengths) because selection of the absorption of a specific wavelength from a polychromatic IR source is difficult to achieve.
One main advantage of optical techniques is that they make monitoring of concentration dynamics in near real time possible, including monitoring several gases with different concentrations at the same time (Powers and Capelari, 2016). Advantages of optical instruments include linear responses over a wide range of concentrations and the ability to measure concentrations both inside (where there could be a high concentration level) and outside (low concentration level) the animal house with the same instruments. Most optical instruments have response times adapted to measurement in animal houses. They are portable and can be used on site. Nevertheless, they can be expensive, must be calibrated, and still require accurate estimation of ventilation rate.

Gas Chromatography
A gas chromatograph separates components in the sample and measures their concentrations. The equipment has four basic elements: an injector, a column, an oven surrounding the column, and a detector. The sample is vaporized in the injector and swept by the carrier gas through a heated column. The column separates each compound according to its polarity and boiling point. The detector identifies and quantifies the compounds separated. The detectors include a flame ionization detector for CH 4 and CO 2 and an electron capture detector for N 2 O. This technique is accurate if the detector has been calibrated for the range of concentrations measured. It requires use of a carrier gas and regular calibration, which makes on-site implementation and continuous measurement difficult. It is often used to measure previously collected samples.

Chemiluminescence
Chemiluminescence is used to measure NH 3 concentration. NH 3 in the sample is first oxidized to N 2 O by a catalytic converter, and then the N 2 O is further oxidized to nitric oxide (NO) at high temperature and an elevated energy state. As the molecules return to a lower energy state, they release electromagnetic radiation at a specific wavelength, which is measured and quantified.

Acid Traps
An acid trap is a standard reference technique for measuring NH 3 . A known volume of air is pumped through an acid solution and recorded (figure 6). The acid solution is later analyzed in the laboratory with a Figure 6. Acid trap configuration. colorimetric or photometric method (Hassouna et al., 2016) to estimate the amount of NH 3 trapped in the solution, as: where V sample (m 3 ) is the volume of air that passed through the solution.
Strong acid solutions are used, such as boric acid, orthophosphoric acid, nitric acid, and sulfuric acid. The trap can be used for a few hours or a few days depending on the NH 3 concentrations in the incoming air, the acid concentration, and volume of acid solution in the vials. Sampling time and concentration should be determined before the experiment as a function of the expected NH 3 concentrations. Two vials with acid solution are used sequentially to avoid saturating a single solution. This technique provides a mean NH 3 concentration over the sampling period and thus is not suitable for studies that require monitoring dynamics of NH 3 concentrations in a house. Nevertheless, as it is not expensive or too time-consuming, it can be used to check the consistency of measurements made, for instance, with optical techniques.

Active Colorimetric Tubes
Active colorimetric tubes are a manual technique that can be used to estimate NH 3 , NO, volatile organic compounds (VOC), and CO 2 concentrations. Tubes are manufactured to react to a specific range of concentrations of a specific target gas. Before measurement, both ends of a sealed test tube are cut open. The tube is connected tightly to a hand pump, which draws air through the tube. If present in the air, the target gas reacts with reagents in the tube. The strength of the reaction is proportional to the concentration of the gas in the air. A graduated scale is used to read the degree of color change in the tube, which indicates the concentration of the target gas. Many of the reactions used are based on pH indicators, such as bromophenol blue to measure NH 3 concentrations. Gas concentration is expressed in ppm or mL m −3 . This technique is reliable and simple to use. It can be used to estimate concentrations, but not to measure them continuously or accurately.

Ventilation Rate
In mechanically ventilated houses with modern ventilation control systems, ventilation rate could be one of many data recorded continuously. In such situations, the data are thus easily available for emission calculations. For other houses, or if the time step of recording is not suitable or recorded data are not reliable, the ventilation rate must be measured or assessed. Different methods to estimate the ventilation rate have been evaluated and described in the literature Wang et al., 2016). The method chosen depends on the type of ventilation (natural or mechanical), the accessibility of the exhaust to make physical measurements, the level of ventilation rate, and the desired degree of accuracy. Some techniques are indirect (tracer gas, heat balance), while others are direct (fan wheel anemometer, specialized instruments).

Tracer Gas Techniques Using Artificial Tracer Gases
Tracer gas techniques are commonly used to quantify the ventilation rate in many kinds of houses, but mainly those with natural ventilation. An external tracer gas should be safe, inert, measurable, not produced in the house, and inexpensive (Phillips et al., 2001;Sherman, 1990). The most common tracer gas used in animal houses is sulfur hexafluoride (SF 6 ) (Mohn et al., 2018). A critical requirement is that of nearperfect air mixing inside the animal house to ensure that the tracer gas and the targeted gas (for emission calculations) being measured both disperse in a similar way. Air can be mixed artificially using a purpose-built ventilation duct ( figure 7). Tracer gases can be dosed automatically using a mass flow controller and critical orifices ( figure 8).
The basic principle for tracer gas techniques is conservation of mass (of both target gas and tracer gas). By monitoring the dosed mass flow and concentration at the sampling points of the tracer gas, the ventilation rate can be determined (figure 9). A tracer gas release  technique is chosen based on the ventilation rate, the detection limit of the device used to monitor tracer gas concentration, and the ability to control and monitor the dosed mass flow accurately. According to Ogink et al. (2013), three tracer gas release techniques can be distinguished: • constant injection method: tracer gas is injected at a constant rate, and its concentration is measured directly over a period of time and used to estimate the ventilation rate; • decay method: tracer gas is injected until its concentration stabilizes, then injection is stopped and the decay in concentration is used to calculate the ventilation rate; and • concentration method: tracer gas is distributed in the air of a house to a certain concentration to be constant.
Only the constant injection method and the decay method are common for measurements in animal houses.
To calculate the emission or mass flow of the target gas (e.g., NH 3 , CH 4 ), a background correction of the concentration (C x ) must first be calculated for the target gases and the tracer gases: The ratio of the background concentrations of emitted (target) gas, C G , and tracer gas, C T , then corresponds to the ratio of their mass flow rates ( m, g d −1 ): and thus

Carbon Dioxide (CO 2 ) Mass Balance or Tracer Gas Methods Using an Internal Tracer
The CO 2 mass balance method is sometimes considered a tracer gas technique in which CO 2 is used as an internal tracer, that is, not dosed but produced by animal respiration and manure. It can be used in naturally or mechanically ventilated houses. It is based on the hypothesis that ventilation rate determines the relationship between CO 2 production in the house and the difference in CO 2 concentrations between the inside and outside of the house. This method has been widely described (Blanes and Pedersen, 2005;Estellés et al., 2011;Samer et al., 2012) and is more accurate in buildings with no litter and no gas heating system. where the total heat produced for the entire house is expressed in heat production units (hpu; 1 hpu is 1 kW of total animal metabolic heat production at 20°C) and the ventilation flow per hpu is in m 3 h −1 hpu − 1 .
The International Commission of Agricultural Engineering provides a method to calculate total heat production (sensible plus latent) for different animal categories (Pedersen and Sällvik, 2002). For instance, for fattening pigs, the total heat produced for the entire house is calculated by multiplying the total heat per animal (in W animal − 1 ) by the number of animals and converting to heat production units as: total heat per house total heat per animal number of animals u where m = animal mass (kg) n = feed energy in relation to the heat dissipation due to maintenance (g d − 1 ) Ventilation flow per hpu varies as a function of animal activity at different times of the day and difference between indoor and outdoor CO 2 concentrations: where c = CO 2 production (m 3 h −1 hpu − 1 ); varies as a function of animal type (Pedersen and Sällvik, 2002;Pedersen et al., 2008). CO 2,indoors and CO 2,outdoors = measured indoor and outdoor CO 2 concentrations at time h (mL m −3 ) Relative animal activity is calculated as: min 2 Relative animal activity 1 sin where a=constantexpressingamplitudewithrespecttotheconstantvalue1,which is a scaling factor based on empirical observation and which varies depending on the animal type (Pedersen et al., 2008) h=timeatsampling(thisshouldbeadecimalnumber0≤h≤24),e.g., (2:10=2.2) h min = activity factor that relates to the time of day with minimum activity (hours after midnight) (Pedersen and Sällvik, 2002)

Use of Sensors
Fan wheel or hot wire anemometers can be used to quantify ventilation rate in mechanically ventilated houses that draw outlet air through ducts or exhaust fans. One important requirement is having access to exhaust flow where the measurements are to be made, which is not possible in many animal houses. The anemometer measures air velocity, and ventilation rate (VR) is calculated as follows:

VR s A (11)
where s = mean airspeed (m h −1 ) A = cross-sectional area of the ventilation duct or air stream (m 2 ) Proper methods must be utilized to obtain representative mean air velocity over the flow area, for example by selecting a sufficient number of measurement points and applying either log-linear or log-Tchebycheff rules (ISO 3966, 2008) for measurement points spacing.
Use of anemometers is not recommended in naturally ventilated houses because of their rapid change in air fluxes and large size of the open area, which would require many sensors to obtain a representative estimate of the ventilation rate.
In mechanically ventilated houses, continuous monitoring of the static pressure differential and the operating status (on-off) of each fan can be used to estimate the fan's ventilation rate based on its theoretical or measured performance characteristics. Ideally, the in situ performance of each fan is determined first, and the house ventilation rate can be estimated by summing all operating fan flow rates. For example, Gates et al. (2004Gates et al. ( , 2005 developed and improved a fan assessment numeration system (FANS) to measure the in situ performance curve of ventilation fans operating in a negative pressure mechanically ventilated animal house (figure 10). This unit is placed either against a fan on the inside of the house, or at the fan exterior with appropriate flexible ducting (Morello et al., 2014) to direct all airflow through the unit. A series of anemometers traverse the entire flow area to obtain a single mean air velocity, which is multiplied by the calibrated unit cross sectional area. A series of these measurements taken at different building static pressures provides an empirical fan performance curve, obtained, for example, from the regression equation of measured flow on building static pressure. Then, measurements of fan run-time and concurrent static pressure can be used to determine reasonably accurate airflow rates for each fan, and their sum is the building ventilation rate. Previous work has clearly shown that neglecting to account for building ventilation by means of direct measurement results in substantial loss in accuracy of estimates for ER, due to the variation among fans.

The Mass Balance Approach for a Global Estimation of N and C Emissions and Emissions Measurement Validation
A mass balance approach estimates emissions based on changes in livestock over time, without the need to measure emissions directly (figure 11). The approach estimates total N or C emissions rather than emissions of specific gases (e.g., N-NH 3 , N-N 2 O, N 2 , C-CH 4 , C-CO 2 ) or emission dynamics. The accuracy of mass balance calculations depends on the technical and livestock management data available, characterization of the manure and feed, and, in certain cases, the length of the period considered. To test the validity of the data used to calculate an N or C mass  Gates et al. (2005) to describe the performance curve of a ventilation fan in an animal house. The unit can be used on either the inlet or exhaust side of the ventilation fan.
balance, those of non-volatile elements such as phosphorus (P) and potassium (K) must be calculated. As the latter elements are non-volatile, their mass balance deficits (difference between inputs and outputs) should be zero, but the data used in calculations will have uncertainty, especially under commercial conditions. If the mass balance deficit for P and K is too high (e.g., > 15%), then the estimates of total N and C emissions must be reconsidered.
The estimation of N, C, or water emissions (X emissions, where X is for N, C, or water) over the production period can be calculated according to the following equation: inputs outputs e missions X X X X inputs and X outputs are the quantity of X in all inputs and outputs. The estimation of these quantities requires careful data collection (quantities, chemical compositions) concerning animals, feed, eggs or milk (a function of animal production), litter, manure, and animal mortality. Models should be used to estimate the quantity of X in animals as a function of their weight.

Applications
Implementing the different emissions measurement methods in an animal house requires the development of a protocol based on the objectives of the project, the specifics of the animal house, the interior environment, and outdoor weather. Three important points that should be considered in a protocol concern the sampling, the data acquisition, and the validity check of the measurements.

Sampling and Sensor Locations
Evaluation of gas emissions requires measurement of inlet and outlet gas concentration. Sampling at air inlets or outlets is recommended if they can be identified, if their locations are fixed over the measurement period, and if they can be easily reached. When these conditions cannot be fulfilled, multiple locations inside the house are usually selected to provide a mean indoor concentration to accommodate spatial variability of indoor concentration. The same should be done for outdoor concentration. The presence of animals inside the animal area makes installation of gas sensors or sampling tubes more complicated. Ideally, they should be installed when no animals are in the house, such as during an outdoor or vacancy period. They should be located where animals cannot bite, bump, or move them, and should be carefully protected from animals (figure 12). Successful sensor placement requires a trade-off between minimizing animal disturbance and maximizing the representativeness of measurements.
The environment inside animal housing is generally harsh for sensors and the air sampling system. Direct exposure to the combination of humidity, NH 3 , and suspended particulate matter can damage the sensors ( figure 13). Furthermore, indoor air is generally warmer and more humid than outdoor air because of animal heat production or the use of a heating or cooling system inside the house. These differences should be considered when sampling indoor air; for example, sampling tubes should be heated and insulated if air samples are analyzed in a cooler place and condensation within sampling lines might be expected.

Data Acquisition
During the production period, emissions can vary greatly during a 24-hour cycle and over longer time intervals. Variability is due to the same parameters that affect spatial variability, changes in animal behavior, their excretion patterns and quantity, and whether or not they have outdoor access. For instance, fattening pigs and poultry will excrete more total ammonia nitrogen (TAN) each day as they grow, yielding ever higher potential for NH 3 emissions. These two kinds of temporal dynamics (daily and production period) must be considered when measuring gas emissions.
Information concerning the production conditions (number of animals, feed and water consumption, animal mortality) and outdoor climate are also required for validation of measurements and comparison with emissions data already published. All operations made by the farmers or operators (for instance, feeding changes, litter supply, or cooling system implementation) and specific events (for instance, electric power shutdown) during the measurement period should be noted because they will be helpful for data analysis and interpretation.

Validation of Measurements
In order to achieve good quality measurements, data validation steps are necessary at several levels: • Validation measurements for parts or the whole measuring setup should be carried out in advance, especially if the setup, single components, and/or the measurement objective (e.g., housing system) was not measured in this configuration before. • Calibration of analytical devices and sensors has to be performed according to their specifications. For some analytical instruments, measurements with a reference method (e.g., acid traps for NH 3 ) are recommended. • Frequent checks of operational mode and measurement values as well as housing and management conditions are necessary. • Plausibility checks of raw data and emission values (e.g., comparison of courses of gas concentrations and wind speed, data check in view of a predetermined plausible range based upon user scientific and technological knowledge) help to find outliers, non-logical values, etc. These incorrect values have to be eliminated according to predefined criteria. • Redundancy in measurements can enhance the reliability of the values.
For instance, CO 2 concentrations could be measured with both a gas chromatograph and an optical gas analyzer during startup or periodically over the project. • Comparison of the cumulative emissions for N and carbon (C) with N and C mass balance deficits over the measuring period.

Example 1: Calculate ammonia (NH 3 ) emission rate from a mechanically ventilated pig house using the carbon dioxide mass balance approach
Problem: The following case study is based on a project undertaken on behalf of the Irish Environmental Protection Agency to test the suitability of existing NH 3 emission factors currently being used for different pig life stages and to explore the potential impact on Natura 2000 sites (i.e., Special Areas of Conservation and Special Protection Areas that may be sensitive to N). The monitoring equipment is described in detail by Kelleghan et al. (2016). The house used mechanical ventilation, with air inlets along the side of the house and ceiling exhaust fans, but no access to the exhaust stream for direct measurement of ventilation rate. Gas concentrations were measured at 10 a.m. in a house with 406 fattening pigs of 81.25 kg animal − 1 reared on a fully slatted floor. Indoor NH 3 concentrations in the house were measured using a Los Gatos Research ultraportable ammonia analyzer (UAA) in combination with an eight-inlet multiport unit allowing for multiple sampling points. Outdoor concentrations were not measured; for the purposes of this study and the calculations, they were assumed to be zero. Indoor and outdoor CO 2 was measured in the sample gas drawn by the UAA using a K30 CO 2 sensor (Senseair, Sweden). Measured gas concentrations are presented in table 1. Additional parameters adapted for finishing pigs are included in table 2. Calculate the building ventilation rate and the NH 3 emission rate.

Solution:
Calculate the building ventilation rate using the CO 2 mass balance approach expressed by equation 6: VR total heat per house ventilation flow per hpu 1000 × =

(6)
To calculate the total heat per house, first, calculate the relative animal activity with equation 10 using the given values:   The NH 3 emission rate for this example is 45.7 mL s −1 . This equates to 9.7 g day − 1 animal − 1 .

Problem:
This example is based on investigations carried out in experimental dairy housing for emission measurements (Mohn et al., 2018). The housing consists of two experimental compartments, each for 20 dairy cows, and a central section for milking, technical installations, an office, and analytics. The experimental compartments are naturally ventilated without thermal insulation and with flexible curtains as facades.
The diluted tracer gas, SF 6 , was dosed continuously through steel tubes with critical capillaries (every third meter) next to the aisles to mimic the emission sources. Stainless steel tubes and critical orifices were protected with metal profiles from damage by animals and contamination with excrement. To adjust analyzed tracer gas concentration in an optimal range (> 0.05 μg m −3 , < 1.5 μg m −3 SF 6 ), tracer gas flow was set according to meteorological and ventilation conditions (e.g., curtains open/closed) by mass flow controllers. Integrative air samples at a height of 2.5 m with a piping system consisting of Teflon tubes and critical glass orifices (every second meter) allow a representative sample. Teflon filters protected the critical orifices from dust and insects. Flow rates for individual orifices of the dosing and sampling systems were monitored before and after every measuring period using mass flow meters. The analytical instrumentation for CH 4 (cavity ring-down spectrometer, CRDS, Picarro Inc., Santa Clara, CA, USA) and SF 6 analysis (GC-ECD, Agilent, Santa Clara, CA, USA) was located in an air-conditioned trailer in the central section. The two compartments were sampled alternately for 10 min. each. Further, once per hour, the background (approximately 25 m from housing, unaffected by the housing) was sampled, so at least two 10-min samples per compartment were obtained every hour.
To describe the measurement situation, relevant accompanying parameters such as housing and outdoor climate, animal parameters (e.g., live weight, milk yield, milk composition, milk urea content, urine urea content), and feed (quality and quantity, amount of trough residue) were recorded.
Calculate the CH 4 emissions during one 10-min measurement taken on 23 September at 12:40 p.m. in a compartment with perforated floors holding 20 cows. The measured gas concentrations are presented in table 3.

Solution:
Calculate the background correction (C x ) according to equation 3 using mea-        by Gates et al. (2005) to describe the performance curve of a ventilation fan in an animal house. Note the unit can be used on either the inlet or exhaust side of the ventilation fan.